BOYA  |  SKU: PVMS20375  |  UPC/GTIN : 6971008023831

BOYA BY-M1000 Large Diaphragm Condenser Microphone

Rs. 6,495.00 Rs. 16,995.00

Offers

  • Get GST invoice and save up to 28% on business purchases.
  • EMI option available.

Delivery and Shipping

USUALLY SHIPS IN 24 HOURS

Pickup

Pickup also available at PhotoVatika Head Office.

Usually ready in 4 hours.

The BOYA BY-M1000 is a large-diaphragm condenser designed for recording in studio applications. Use it for miking vocals or instruments around your studio. It offers three polar patterns: cardioid, omnidirectional, and figure-8. All three polar patterns have their uses in the studio environment.

Omnidirectional gives you an even phase and frequency response all around the capsule. Cardioid deadens the back of the capsule, allowing you to mic sources closer to walls; this is the preferred polar pattern of the project or home studio. Figure-8 deadens both sides of the capsule, while the front and back have the same frequency and phase response; this is a wonderful choose for mono-miking two instruments while minimizing room coloration.

The mic itself boasts a smooth and flat frequency response between 20 Hz and 20 kHz. The two-position low-cut filter can help mitigate some rumble and clean up the signal in situations where low-end frequency is not wanted. The -10 dB pad is a boon when miking loud sources, such as drums. Switches for both are found on the mic itself.

The mic is fashioned out of metal, and runs off 24 to 48V phantom power, supplied from your preamp, console, or interface. A 10' mic cable is included, as is a shockmount, a pop filter, and a 3/8 to 5/8" thread adapter to accommodate all manner of mic stands.


Key Features at a Glance
Large gold-sputtered diaphragm
Great for studio and broadcast
Flat, wide-range frequency response
Omnidirectional, Figure-8, and Cardioid pickup pattern
Switchable low-cut filter at 150 Hz
Selectable -10 dB pad
Included shockmount and pop filter
24 or 48V phantom power
Standard XLR connector
10' XLR cable included
Included 3/8" and 5/8" threads


Specifications
Form Factor

Stand/Boom Mount

Sound Field

Mono

Capsule

Condenser

Diaphragm

1.34" / 34 mm (Condenser)

Polar Pattern

Cardioid, Figure-8, Omnidirectional

Pattern Selection

Switched (Adjustable on Mic)

Orientation

Side Address

Circuitry

Solid-State

Pad

-10 dB

High-Pass Filter

150 Hz

On-Board Controls

Polar Pattern, High-Pass Filter, Pad

Frequency Range

20 Hz to 20 kHz

Impedance

200 Ohms

Sensitivity

-33 dB

Signal-to-Noise Ratio

80 dB

Output Connectors (Analog)

1 x XLR 3-Pin Male (on Mic)

Cable Length

10' / 3.05 m

Operating Voltage

24 to 48 V (Phantom Power)

Color

Black

Mounting

Shockmount (Included)

Construction Material

Metal

Dimensions

ø: 4.53 x H: 8.15 x W: 7.28" / ø: 115 x H: 207 x W: 185 mm

Weight

28.64 oz / 812 g

Package Weight

2.485 lb

Box Dimensions (LxWxH)

9.6 x 8.1 x 6.1"

Payment & Security

Payment methods

    Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

    BOYA BY-M1000 Large Diaphragm Condenser Microphone
    BOYA

    BOYA BY-M1000 Large Diaphragm Condenser Microphone

    Rs. 6,495.00 Rs. 16,995.00
    The BOYA BY-M1000 is a large-diaphragm condenser designed for recording in studio applications. Use it for miking vocals or instruments around your studio. It offers three polar patterns: cardioid, omnidirectional, and figure-8. All three polar patterns have their uses in the studio environment.

    Omnidirectional gives you an even phase and frequency response all around the capsule. Cardioid deadens the back of the capsule, allowing you to mic sources closer to walls; this is the preferred polar pattern of the project or home studio. Figure-8 deadens both sides of the capsule, while the front and back have the same frequency and phase response; this is a wonderful choose for mono-miking two instruments while minimizing room coloration.

    The mic itself boasts a smooth and flat frequency response between 20 Hz and 20 kHz. The two-position low-cut filter can help mitigate some rumble and clean up the signal in situations where low-end frequency is not wanted. The -10 dB pad is a boon when miking loud sources, such as drums. Switches for both are found on the mic itself.

    The mic is fashioned out of metal, and runs off 24 to 48V phantom power, supplied from your preamp, console, or interface. A 10' mic cable is included, as is a shockmount, a pop filter, and a 3/8 to 5/8" thread adapter to accommodate all manner of mic stands.


    Key Features at a Glance
    Large gold-sputtered diaphragm
    Great for studio and broadcast
    Flat, wide-range frequency response
    Omnidirectional, Figure-8, and Cardioid pickup pattern
    Switchable low-cut filter at 150 Hz
    Selectable -10 dB pad
    Included shockmount and pop filter
    24 or 48V phantom power
    Standard XLR connector
    10' XLR cable included
    Included 3/8" and 5/8" threads


    Specifications
    Form Factor

    Stand/Boom Mount

    Sound Field

    Mono

    Capsule

    Condenser

    Diaphragm

    1.34" / 34 mm (Condenser)

    Polar Pattern

    Cardioid, Figure-8, Omnidirectional

    Pattern Selection

    Switched (Adjustable on Mic)

    Orientation

    Side Address

    Circuitry

    Solid-State

    Pad

    -10 dB

    High-Pass Filter

    150 Hz

    On-Board Controls

    Polar Pattern, High-Pass Filter, Pad

    Frequency Range

    20 Hz to 20 kHz

    Impedance

    200 Ohms

    Sensitivity

    -33 dB

    Signal-to-Noise Ratio

    80 dB

    Output Connectors (Analog)

    1 x XLR 3-Pin Male (on Mic)

    Cable Length

    10' / 3.05 m

    Operating Voltage

    24 to 48 V (Phantom Power)

    Color

    Black

    Mounting

    Shockmount (Included)

    Construction Material

    Metal

    Dimensions

    ø: 4.53 x H: 8.15 x W: 7.28" / ø: 115 x H: 207 x W: 185 mm

    Weight

    28.64 oz / 812 g

    Package Weight

    2.485 lb

    Box Dimensions (LxWxH)

    9.6 x 8.1 x 6.1"
    View product